Fiber cement pressure plate as a partition board is a very good material, fiber cement pressure plate has high strength, high density, the most important is not easy to deformation, corrosion resistance, fiber cement pressure plate has exceeded the standard requirements of partition board, let's take a look at the installation process of fiber cement pressure plate.

There are several steps in the installation of fiber cement pressure plate

1. Prepare for installation. 2. Inspection, correction, 3. Support reinforcement. 4. Welding and fixing. 5. Rush to sew.

A construction method of fiber cement pressure plate as partition wall

1. One is to be able to follow the structural construction and hoist the slab into the device and weld it before the floor is buckled; the other is to lift the required wall of each room into the room before fastening the floor slab, and place it against the wall firmly for future manual installation.

2. Check and proofreading: check the type of device to prevent the occurrence of wrong plate number. During installation, wedge shall be placed according to the marked azimuth line on the floor, the wall panel shall be placed stably, and the wall panel shall be temporarily supported and clamped with clamps at the lifting ring position. Recheck the orientation of the device, adjust the deviation, and use the supporting wire board for straight proofreading.

3. Support reinforcement: check the horizontal and vertical directions of the fiber cement pressure plate. In the future, support should be added to the lifting ring to tighten the wedge at the bottom of the plate to prevent displacement and inclination. The appropriate height of the joint under the plate is 2030 mm. It is forbidden to place the fiber cement pressure plate directly on the floor without any treatment. 3. Welding fixation: after the orientation of the fiber cement pressure plate is checked, the embedded parts on the board and the embedded parts on the structural wall (or between the fiber cement pressure plates) are firmly welded with the connecting steel plate. It is necessary to do three-sided welding, and the embedded parts shall not protrude from the structural wall.

4. Caulking: after the fiber cement pressure plate is welded safely, the four surrounding gaps are filled with 1:2.5 cement mortar, and the mortar is mixed with 10% 107 glue. When the joint width is greater than 30mm, C20 pea stone concrete is used to fill the gap. When the mortar of slab joint has certain strength, the wedge shall be withdrawn and the wedge hole shall be filled. The mortar for slab joint shall be dense and flat, and the internal corner shall be straight, so as to facilitate the installation of 5 devices: there are two methods for the installation of fiber cement pressure plate.

Brief introduction to simplified version of ocean Willy company

Jiangxi ocean Willie Industrial Co., Ltd., established in 2001, is located in Jingdezhen, Jiangxi Province, the "porcelain capital of the world". It is a professional R & D and manufacturer of fiber cement board, the solution of building system with fireproof board and prefabricated housing wall. It is a national high-tech enterprise and a listed reserve enterprise in Jiangxi Province. "Ocean Willy" trademark is a famous trademark in Jiangxi Province, which has passed ISO9001 quality management system certification, ISO14001 environmental management system certification and CE EU certification, and is listed as one of the key enterprises of comprehensive utilization of environmental protection and energy-saving resources.

The company implements the three product strategy of "emphasizing brand, strengthening quality and excellent products", implements the project sales management mode of "production, technology and engineering Trinity", relying on the advantages of local resources, independently develops and produces "ocean Willy" brand series products, including low, medium and high density fiber reinforced cement board, Jianyuan low density board, clear water wall rock plate, wall rock color plate, FCA steel Structural floor, fireproof and anti sinking ceiling, fireproof perforated sound-absorbing board and fireproof FCA board. It is a well-known and influential manufacturer of grade A1 fireproof board products in Jiangxi Province.

"Ocean Willy" series of fire and environmental protection board has the advantages of fire prevention, moisture-proof, heat preservation, durability, sound insulation, heat insulation, light weight, high strength and environmental protection. Ocean Willy series plates can completely cover and replace all the plate materials and non load bearing wall materials in a building.

The company's products are widely used in Qinshan nuclear power station, high-speed railway station, State Grid Substation, many five-star hotels, Grade-A office buildings, Grade-A hospitals, landmark public buildings, etc. In the foreign market, after more than ten years of efforts, the company's products have been exported to the Middle East, Southeast Asia, Africa, Latin America, Europe, the United States and other 50 countries and regions. "Ocean Willy" series products enjoy high popularity at home and abroad, winning the unanimous recognition of customers at home and abroad.